Stylin Rydz

05/31/2026

FC RX-7 Wiperless Hatch Glass & Hatch Assembly – $200

Clean FC RX-7 hatch with wiperless glass in good shape. The hatch and glass are both solid, with no major issues.

The lower seal where the hatch meets the center section is starting to come loose—a very common FC RX-7 issue and should be an easy fix for the next owner.

✅ Wiperless glass
✅ Hatch in good condition
✅ Glass in good shape
✅ Great replacement or upgrade piece

$200 – Local pickup in Coaling, AL

First come, first served. Bring your FC back to its glory days without hunting down another hatch! 🚗💨

05/05/2026

We had this unit dropped off last week for a full check-over. After completing the initial inspection, the customer put it to work over the weekend and identified a few weak points that needed attention.

Since then, we’ve taken care of several issues. We repaired the loose track, secured the pins that were backing out, and addressed leaks in the hydraulic lines. We also fixed the hood latch, which had come apart.

Next, we’ll be completing a full engine oil and filter change, along with a hydraulic filter replacement and fluid flush to keep everything running smoothly.

Lastly, the exhaust that broke will be repaired — no problem for our team. 🫡

We’re making sure this unit goes back out stronger, tighter, and ready to perform. 💪

If you or anyone you know needs or wants this type of work done, don’t be afraid to hit us up!!!

05/05/2026

This Malibu that got dropped is getting the works!!

This will be a few months project but it will be mean and done right!!

We have torn the whole front end down and started from scratch!

This unit has gotten some bad to the bone parts installed as of new tubular control arms upper and lowers along with a brake line kit for the front and rear brakes.

We installed a new tubular support as the car will be getting a big turbo so room is much needed, we have installed a new driveshaft loop as well as front Viking coilovers and it’s getting front wilwood brakes to make the rears! We are just getting started on this and it will be one bad machine!

If you or anyone you know wants or needs this type of work done, don’t be afraid to hit us up!!!

05/05/2026

This box Chevy is almost ready to hit the streets—just waiting on a few final parts to bring it all together.

We’ve been putting in serious work on this build, turning it into a clean, hard-hitting ride that sounds as good as it performs with that stage 2 cam.

When it first came in, it needed some attention. We pulled the engine and transmission to address torn motor and trans mounts, then upgraded it with a new stall converter to properly match the cam. While we were in there, we also took care of some transmission issues to make sure everything runs strong and smooth.

From there, we kept leveling it up:
• New U-joint installed in the driveshaft
• Fresh MSD ignition box—fully tuned in-house
• New starter installed
• Frame modified for proper header fitment

And we didn’t stop there… 💪

We added an accessory bracket kit, alternator, new fuel tank with fuel lines and sending unit, front brake lines, radiator hoses, and radiator support brackets. Custom transmission lines were built, and a new trans cooler was mounted up front for optimal performance.

To top it off, we wired the full ignition system, fuel pump, fans, and alternator setup—and tucked everything clean for that polished, professional finish.🤝

This one’s coming together exactly how it should: clean, reliable, and ready to turn heads while beating the pavement.🔥

If you or anyone you know wants or needs this type of work done, don’t be afraid to hit us up!!!

05/05/2026

This Cadillac came to us from another shop with a recommendation for a full transmission replacement. Before moving forward, we performed a thorough diagnosis—and the results told a different story.

We discovered the transmission was extremely low on fluid due to a leak. After repairing the leak and restoring proper fluid levels, we turned our attention to another issue: the vehicle wouldn’t start. Our team replaced the fuel lines, installed a brand-new fuel pump, recharged the battery, and brought the engine back to life.

To ensure long-term reliability, we also addressed the charging system by installing a new alternator with a modern one-wire conversion. Along the way, we added new belts, spark plugs, plug wires, and a fresh air filter.

We finished things off with a complete oil and filter change—leaving this Cadillac running strong and ready to hit the road once again.

Another great example of why proper diagnosis matters. 🚗💪

If you or anyone you know wants or needs this type of work done, don’t be afraid to hit us up!!!

05/05/2026

This little S10 rolled into the shop a couple weeks back needing some serious TLC to get back on the road—and we were happy to bring it back to life 🔧

We started with a full battery relocation, then stepped things up by installing a fuel cell, rear-mounted filter, and a Holley fuel pump. From there, we ran all new fuel lines, added a regulator, and set it up with a brand-new carburetor and mounting brackets for a clean, reliable fuel system.

Electrical got some attention too—we tracked down key switch power, wired up electric fans and the fuel pump to a custom switch setup (just how the customer wanted), and relocated the fuse box for a cleaner layout.

To wrap it up, we handled routine maintenance with fresh oil and a new filter—but not before tackling a failed starter with a brand-new replacement.

Now this S10 is running strong and ready for the road again 💪

If you you or anyone wants or needs this type of work done, don’t be afraid to hit us up!!!

05/01/2026

If we did a run of hats who all would be interested??

We already have 6 presold so let us know if you want one and we can put you down!

Cost would be $25 since it’s such a small batch!

They will be flexfit L/XL fit with a semi curve bill, supper comfy and premium material!

04/15/2026

04/14/2026

The shop is officially FULL — with a growing waitlist behind it! 🙌

We’re loving the momentum and especially excited to see more hot rods and classics rolling in for serious upgrades (and customers ready to invest in doing things right 🔧🔥).

Here’s what’s currently in the shop:

• Malibu – Getting a full front suspension overhaul to match the rear, upgraded front brakes, and some custom fab work you’ll definitely want to stay tuned for 👀

• Coupedeville – Came in for a transmission, but we’re diving deeper with additional upgrades. Already knocked out new fuel lines and pump and got it running strong 💪

• S10 – In for wiring, fuel system work, and final details to get it dialed in

• Box Chevy – Wrapping up an LS swap with wiring, finishing touches, and getting it ready for a proper tune

• Geo Tracker – Going all-in with a turbo kit, multiple upgrades, and a full tune 🚀 (not pictured)

We truly appreciate the continued support — it means everything to see builds like these coming through the door.

If you (or someone you know) are looking for quality work like this, don’t hesitate to reach out. Let’s build something awesome.

03/31/2026

The sweet little RX-7 is back in the shop for some A/C upgrades—and things are coming together nicely.

We’re installing a complete modern RX-8 A/C conversion kit into this FD RX-7, which requires a bit of custom fabrication to integrate seamlessly with the existing engine bay setup. So far, we’ve removed the old A/C components, including the condenser, lines, and compressor, and replaced them with updated conversion brackets, an RX-8 compressor, and a new condenser.

Everything has been progressing smoothly… until we hit a small snag. The A/C line fittings for the evaporator were incorrectly ordered, so we’re taking a moment to correct that before moving forward.

Once that’s resolved, we’ll be back on track to delivering a clean, modern A/C system that performs as good as it looks. Stay tuned—this build is turning out sweet.

If you or anyone you know needs or wants this type of work done, don’t be afraid to hit us up!!